HOW TO SOLVE THE PROBLEMS OF OUR POOL WATER? – MessHall

HOW TO SOLVE THE PROBLEMS OF OUR POOL WATER

Water turbid, whitish

Possible causes:

  • Poor filtration
  • High pH
  • Excess organic waste
  • Hard Water

Steps for Solution:

  • Check the operating status of the filter.
  • Take a filter backwash.
  • Add 1 l of liquid flocculant per 100 m3 of water.
  • Analyze and adjust pH between 7.2 and 7.4.
  • Add 15 g of granulated Dichloro per m3 of water.
  • Keep chlorine between 1 and 1.5 ppm.
  • At night, with the detainee filter adds flocculant. The next morning, all particles will have settled to the bottom.
  • Put the filter valve to “WASTE” and passes the cleaner.
  • Filter for several hours and then make a sand WASH.
  • If the water has high hardness, add some product Antical.

Green water

Possible causes:

  • Algae

Steps for the solution:

  • Perform shock chlorination with 15 g of dichloro granules per m3 of water.
  • Add 3.5 liters of algaecide per 100 m3 of water.
  • Adjust the pH between 7.2-7.4.
  • 8 hours after the shock treatment done, brush the walls and bottom of the pool.
  • Put the filter valve to “WASTE” and sucks the dead algae with sending cleaner water directly to the drain.
  • Put the filter valve in position “WASH” to wash the sand.
  • Increasing the daily dose of chlorine and algaecide.

Brown or colored water

Possible causes:

  • Presence of salts arising from a drop in the pH of the water.
  • Sales of copper = blue / green
  • Sales of iron and manganese = brown

Steps for its solution:

  • Adjust the pH between 7.2 and 7.4.
  • Add 15 g Granulated Dichloro per m3 of water.
  • Then, add 1 liter of liquid loculante F per 100 m3 of water.
  • At night, in calm water, adds a decanter and leave on until morning.
  • With the filter set to “WASTE” passes the cleaner to remove particles that have settled to the bottom,
  • pouring all the dirt down the drain.

Stains on walls

Possible Cause:

  • Presence of metal ions

Steps for its solution:

  • Empty the pool and clean the spot with Extra Desincrustante surfaces.

Inlays

Possible Cause:

  • Precipitation of calcium salts in water

Steps for its solution:

  • Adjust the pH between 7.2 and 7.4.
  • Add a weekly Extra Anti-Limestone.

Water has foam

  • Excessive concentration of algaecide.
  • Organic waste in the water: suntan lotion, sweat, etc. ..

Steps for its solution:

  • Evacuating a portion of the respective drain water (as needed) and filled with new water.
  • With the filtration equipment in position “BYPASS” made a shock treatment.
  • Adjust the pH between 7.2 and 7.4 and the free chlorine level between 1 and 1.5 parts per million (ppm.).
  • Use an algaecide product without foam.

Eyes and / or skin irritated and water an unpleasant smell chlorine

Possible Cause:

  • Presence of chloramines and free chlorine low.

Steps for its solution:

  • Adjust the pH between 7.2 and 7.4 with an increaser or pH reducing product.
  • Make a shock treatment or use a chlorinated product.
  • Keep the chlorine level between 1 and 1.5 ppm.
  • Spend the cleaner and filters the water throughout one day.

Irritated eyes, bleached hair tissues and gives off an odor but NO

Possible Cause:

  • Excess free chlorine.

Steps for its solution:

  • Decrease the daily dose of chlorine to a level between 1 and 1.5 ppm

Eyes, skin and irritating odors are

Possible Cause:

  • unadjusted pH
  • Excess organic waste

Steps for its solution:

  • Analyze the pH and adjust it between 7.2 and 7.4.
  • Perform a chlorination with 15 g of dichloro granules per m3 of water.

Leave a Reply

Your email address will not be published. Required fields are marked *